Diff for "VectorviewDescription" - Meg Wiki
location: Diff for "VectorviewDescription"
Differences between revisions 23 and 26 (spanning 3 versions)
Revision 23 as of 2013-02-04 15:05:24
Size: 2364
Editor: OlafHauk
Comment:
Revision 26 as of 2021-06-23 14:29:12
Size: 2496
Editor: OlafHauk
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
attachment:mrclogo.gif {{attachment:mrclogo.gif}}
Line 3: Line 3:
= The Elekta Neuromag Vectorview System = = MEGIN Vectorview and Triux Sensor Layout =
Below you will find a short description of [[#Magsgrads|magnetometers and gradiometers]], as well as our [[#MEGsensors|MEG sensor]] and [[#EEGlabels|EEG electrode]] layouts.
Line 5: Line 6:
Below you will find a short description of [#Magsgrads magnetometers and gradiometers], as well as our [#MEGsensors MEG sensor] and [#EEGlabels EEG electrode] layouts. The [[#Elektamanuals|Elekta manuals]] are at the bottom.
Line 7: Line 8:
The [#Elektamanuals Elekta manuals] are at the bottom.

Figures are from the Elekta Neuromag System [attachment:HardwareUser.pdf Hardware User's Manual].  
Figures are from the Elekta Neuromag System [[attachment:HardwareUser.pdf|Hardware User's Manual]].
Line 15: Line 13:
[[Anchor(Magsgrads)]]
attachment:MagsGrads.jpg
<<Anchor(Magsgrads)>> {{attachment:MagsGrads.jpg}}
Line 22: Line 19:
[[Anchor(MEGsensors)]]
attachment:SensorLayout.jpg
<<Anchor(MEGsensors)>> {{attachment:SensorLayout.jpg}}
Line 25: Line 21:
attachment:SensorLabeling.jpg {{attachment:SensorLabeling.jpg}}
Line 27: Line 23:
We routinely use a '''70-electrode EEG set-up''' (Easycap) in combination with our MEG recordings. This is the electrode layout: We routinely use a '''64-electrode EEG set-up''' (Easycap) in combination with our MEG recordings. This is a subset of the following electrode layout (it was changed after the latest system upgrade, please contact OlafHauk for details):
Line 29: Line 25:
[[Anchor(EEGlabels)]]
attachment:ElectrodeLayout.jpg
<<Anchor(EEGlabels)>> {{attachment:ElectrodeLayout.jpg}}
Line 33: Line 28:
[[Anchor(Elektamanuals)]] <<Anchor(Elektamanuals)>>
Line 35: Line 30:
[attachment:HardwareTechnical.pdf Hardware Technical Manual] [[attachment:HardwareTechnical.pdf|Hardware Technical Manual]]
Line 37: Line 32:
[attachment:HardwareUser.pdf Hardware User's Manual] [[attachment:HardwareUser.pdf|Hardware User's Manual]]
Line 39: Line 34:
[attachment:DataAcquisition.pdf Data Acquisition Manual] [[attachment:DataAcquisition.pdf|Data Acquisition Manual]]
Line 41: Line 36:
[attachment:StimulusSystem.pdf Stimulus System Manual] [[attachment:StimulusSystem.pdf|Stimulus System Manual]]
Line 43: Line 38:
[attachment:SensorTuner.pdf Sensor Tuner Manual] [[attachment:SensorTuner.pdf|Sensor Tuner Manual]]
Line 45: Line 40:
[wiki:CbuMeg:StandardOperatingProcedures Standard Operating Procedures] [[StandardOperatingProcedures|Standard Operating Procedures]]

mrclogo.gif

MEGIN Vectorview and Triux Sensor Layout

Below you will find a short description of magnetometers and gradiometers, as well as our MEG sensor and EEG electrode layouts.

The Elekta manuals are at the bottom.

Figures are from the Elekta Neuromag System Hardware User's Manual.

Technical description

Our Vectorview systems contains 102 magnetometers and 204 planar gradiometers. Magnetometers consist of a single coil which measures the magnetic flux perpendicular to its surface. Planar gradiometers consist of a "figure-of-eight"-type coil configuration. The measured signal is the difference between the two loops of the "eight", or the spatial gradient. There are two orthogonal planar gradiometers at each location. This arrangement is illustrated in the following figure (black: magnetometer; grey and white: two gradiometers).

MagsGrads.jpg

It has been shown that 3 sensors of these types at one location measure independent information (their "leadfields" are orthogonal). It is therefore more efficient than placing 3 sensors of the same type (e.g. magnetometers) close to each other (they would basically measure the same signal 3 times). Our sensor configuration therefore provides an optimal sampling of the magnetic field for a given number of sensors. The downside is that magnetometers and gradiometers often have to be treated differently during analysis or visualisation.

This is the whole sensor layout, including the sensor labels used by the Neuromag software:

SensorLayout.jpg

SensorLabeling.jpg

We routinely use a 64-electrode EEG set-up (Easycap) in combination with our MEG recordings. This is a subset of the following electrode layout (it was changed after the latest system upgrade, please contact OlafHauk for details):

ElectrodeLayout.jpg

Elekta Manuals

Hardware Technical Manual

Hardware User's Manual

Data Acquisition Manual

Stimulus System Manual

Sensor Tuner Manual

Standard Operating Procedures

CbuMeg: VectorviewDescription (last edited 2021-06-23 14:29:12 by OlafHauk)